Expert Answers about RV Jack Pads
- Recommended SnapPad Jack Pads for Equalizer Leveling System w 10" Octagon Jack Feet
- I recommend the SnapPad EQ Octagon Jack Pads for Equalizer Leveling System w 10" Octagon Jack Feet, # SN76FR a qty of 4.
view full answer... - Snap Pads For 2018 Newmar Bay Star
- Great question.
To get the proper Item and fit I will need to know the size and shape of the feet on your system.
Are they round, square, rectangle. Do they have a lip or raised edge or are they complete flat and level?
The SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 4 # SP54FR4 will work with jack feet that are round and have a 9 inch diameter and no lip or raised edge.
view full answer... - SnapPad XTRA Jack Pads Weight
- The six jack pads in the SnapPad XTRA Pack # SP54FR6 weigh approximately 30lbs.
view full answer... - How to Reset Zero Point Lippert Ground Control 3.0
- Yes, you can reset the Zero Point calibration on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590. You simply need to follow these directions from the linked instruction manual:
1. In manual mode, run the jacks to level the trailer. This is best achieved by placing a level in the center
of the trailer and leveling it both front to back and then side to side. (See “Basic Jack Operation” for
instructions on how to manually operate the system).
2. Once the...
view full answer... - Determining The Correct Size Landing Gear SnapPad Size
- To determine which SnapPad's are right for your 2017 Newmar Canyon Star Motorhome, you'll to first measure the diameter of landing gear foot; be sure to include the 'lip" in this measurement.
If you have 10" landing gear feet, then SnapPad EQ Plus Jack Pads for Equalizer Leveling System w 10" Round and 10" Octagon Feet # SP64FR84 is what you'll need. If you have 8 feet the SnapPad HiWay 8 Jack Pads for HWH Leveling Systems w/ 8" Round Jack Feet # SP34FR4 is what you'll need.
view full answer... - Replacement Jack Foot Pad For Ram 3500-Lb A-Frame Electric Trailer Jack
- We do not offer specific feet for a Ram 3,500-lb A-frame electric jack but we may have a replacement foot plate that will work for you.
I have attached a link to our product page for the replacement jack foot pads that may work for you. For example, if your inner tube measures 2-inches diameter, part # LC165253 may work great for you.
view full answer... - What Size Bolts Used for LC314592 Hydraulic Jack Adapter Lugs
- The bolts for attaching the # LC314592 Jack Adapter Lugs to the landing gear pad like what's used with the # LC191023 stabilizers are actually included.
They are 5/16-18 x 3/4 inch bolts.
view full answer... - Functions of Lippert Touchscreen Remote for Ground Control 3.0 & Does it Have Warranty
- The Replacement Touchscreen Remote w/ Charger for Lippert Ground Control 3.0 Electric Leveling System # LC358601 does have a warranty of one year.
In regards to the functions, I have added a cut out of the manual which shows what the functions of the remote are. It will retract and extend the jacks, but does also give you the auto leveling feature. This system is designed as a replacement remote for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 6-Point Set # LC675817...
view full answer... - Resetting Zero Point on Ground Control
- Thank you for your purchase from etrailer of the Lippert Ground Control 3.0 # LC358590. In order to reset the Zero Point, here is what you need to do, per the manual:
1. In manual mode, run the jacks to level the trailer. This is best achieved by placing a level in the center
of the trailer and leveling it both front to back and then side to side. (See “Basic Jack Operation” for
instructions on how to manually operate the system).
2. Once the trailer is level, turn off the touch pad.
3....
view full answer... - How Much Do the Ark Drop Down Corner RV Stabilizer Jacks Weigh
- The Ark Drop Down Corner RV Stabilizer Jack Kit part # ARK94FR weigh around 30 lbs for the pair.
view full answer... - How To Replace The Heating Pad In A Thomas Payne Seismic Recliner
- You will have to go from the side or underneath. Then you can unplug and remove the old pad and replace it with the Replacement 29-Volt Seat Heating Pad for Thomas Payne Seismic Series RV Couches and Chairs # 674864.
If you need to replace the entire kit you can use the Replacement Seat Heater Kit for Thomas Payne RV Furniture # 195-000113
view full answer... - Can The ThermaHeat RV Holding Tank Heater Pad Be Used With 24v Systems
- Tank heaters like the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000163 are not compatible with 24volt applications and will only operate properly in a 12v system.
view full answer... - Can Spray Foam Be Used Over A ThermaHeat RV Holding Tank Heating Pad
- The manufacturer does not recommend using spray foam over the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000163 as it can can potentially affect its function and may interfere with the surrounding wiring as well.
view full answer... - Can A ThermaHeat RV Holding Tank/Step Heater Pad Be Covered With Spray Foam Insulation
- The ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000164 isn't going to get hot enough to cause an issue with the insulation spray, but I wouldn't recommend it since it would be a pain to remove in the event that it malfunctions and needs to be replaced.
The manufacturer hasn't tested it but recommends not doing it incase the chemicals in the spray foam could cause any kind of damage to the pad or the wiring.
view full answer... - Do the ThermaHeat RV Holding Tank or Step Heater Pads Get Hot to the Touch
- The ThermaHeat RV Holding Tank or Step Heater Pad part # 277-000163 do get hot to the touch but not enough to burn you as they has a 67 degree cutoff. The outside of the pad should not exceed the shutout off temp although there are a few factors to this.
view full answer... - Can ThermaHeat RV Holding Tank Pad be Put on Metal
- No, you should not stick the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat - 25" Long x 7-1/4" Wide # 277-000163 onto any metal surface.
It would not be effective and conducts electricity so you definitely don't want to use the # 277-000163 on that type of surface.
view full answer... - Are Round Replacement Foot Pads for Power Landing Gear an Upgrade
- The Lippert Components 5th Wheel RV Landing Gear Foot Pad # LC314667 are absolutely an upgrade over standard foot pads for power landing gear systems. The reason for that is 2-fold: 1) they are large at 9 inches in diameter which means they are much wider than what you have, helping to distribute weight and 2) they are round, which means they are going to be more stable than a standard rectangular foot because they more evenly distribute the weight.
view full answer... - Can the Lippert Ground Control Jacks Be Retracted When Not Connected To a Truck?
- You can retract the rear jacks of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590 when it not connected to your truck. If you want to retract the landing gear/front jacks you will need to use Jack Stands # PTW41021 that are capable of supporting the weight of the 5th wheel while you retract the jacks. Also be sure the wheels are properly chocked as you do not want the camper to slide on the jack stands.
view full answer... - Choosing RV Ladder Mounted Bike Rack
- Of the ladder mounted bike racks we offer, the Surco # SP501BR model you referenced has the highest weight capacity at 75 lbs. Your combined bike weight is 77 lbs, so if you were to remove the seats from each bike, you'd probably get the load under the 75 lb weight capacity of the rack.
Ladder mounted bike racks are pretty bare-bones, there's not much in the way of padding on them. You can always add padding to the rack. I've found that those pool noodle floatation devices work just great...
view full answer... - How Do The Jacks On The Lippert Ground Control 3.0 Know When to Stop?
- The jacks in the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590 each have sensors. These sensors tell the control module what position each jack is in so that it knows when the jack is fully retracted or fully extended.
The front jacks should be mounted so that when the jack is fully retracted the pull pins will not contact the trailer frame.
view full answer...
Go To Results